Tools You Need to Set Up a New Tub
Tools You Need to Set Up a New Tub
Blog Article
The article author is making several good annotation on the subject of A Step-by-Step Guide to Installing a Bathtub as a whole in this article down the page.
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough task. If the old tub is easily easily accessible, the project can move speedily; if you have to open a wall surface to get rid of the old tub as well as position the new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly require a helper to move out the old tub and embeded in the brand-new one. Make certain you have qualified on your own for the work and also fit trying it. Instead of hiring a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new bathtub in your bathroom if you have actually already acquired a new bathtub as well as don't require to change the setup of your previous water supply pipes.
Your devices and product checklist need to make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making certain that the washers are in location in between the faucet and the sink. Secure the tap in position with the supplier supplied backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former type should be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the tub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Turn on the supply of water and check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bath tub and also check the overflow outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub ought to wait up until the bathtub has been made use of a minimum of once as this will settle it into its last setting.
Planning for the Setup
First of all, the sustaining structure provided with the bath must be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, triggering the water to permeate the wall between the bath as well as the tiling, leading to difficulties with wetness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our excerpt on Installing A Bathtub. Many thanks for taking the time to browse our piece of content. Enjoyed reading our write-up? Please share it. Help another person find it. Thanks for your time. Don't hesitate to come by our site back soon.
Schedule Today
Report this page